Mercedes-Benz SL 320 Operator'S Manual Download Page 27

Page: 27 / 161

Infrared Remote Control

Starter Lock-Out

Important!

Locking the vehicle activates the starter

lock-out.

The engine can only be started, if the

vehicle was unlocked from the outside.

Note:

If transmit button of the remote control

is inadvertently pressed again prior to

starting the engine, the start lock-out is

activated. In this case press transmit

button again to deactivate the start lock-

out.

Transmit button

Transmitter eye and battery

check

The vehicle doors, trunk and fuel filler

flap can be centrally locked and

unlocked, as well as the windows

closed with infrared remote control.

The transmitter is located in the key

holder, the receiver is located on the

inside rear view mirror.

Receiver on inside rear view

mirror

Red indicator lamp (locking)

Green indicator lamp (unlocking)

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands