Mercedes-Benz SL 320 Operator'S Manual Download Page 90

Page: 90 / 161

Brake Pad Wear Indicator Lamp

The brake pad wear indicator lamp in

the instrument cluster comes on when

the key in the steering lock is turned to

position 2 and goes out when the

engine is running.

If the indicator lamp lights up during

braking, this indicates that the front

wheel brake pads are worn down

(vehicles equipped with ASR front

and/or rear wheel brake pads).

Have the brake system checked at your

authorized MERCEDES-BENZ dealer

as soon as possible.

Brake Warning Lamp

The brake warning lamp will come on:

•

when there is insufficient brake

fluid in the reservoir (engine

running and parking brake

released)

•

when the parking brake is set

(engine running)

When the minimum mark on the

reservoir is reached, have the brake

system checked for brake pad thickness

and leaks.

To test the brake warning lamp, turn

the key in steering lock to position 2.

The brake warning lamp comes on, and

should go out when the engine is

running.

Warning!

Driving with the brake warning

lamp on can result in an accident.

Have your brake system checked

immediately if the brake warning

lamp stays on. Don't add brake fluid

before checking the brake system.

Overfilling the brake fluid reservoir

can result in spilling brake fluid on

hot engine parts and the brake fluid

catching fire. You can be seriously

burned.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands