Mercedes-Benz SL 320 Operator'S Manual Download Page 108

Page: 108 / 161

108

Trunk Lamp

Switching off

Switching on

Switch off trunk lamp if the trunk is to

remain open for a long period of time.

This prevents the vehicle battery from

being discharged.

When the trunk lid is closed, the switch

will reset and turn on the lamp the next

time the lid is opened.

Spare Wheel

Trunk floor

Strap

Roll back the floor mat, lift the trunk

floor (1) and engage strap (2) in the

hooks on the upper edge of the trunk lid.

First remove the vehicle jack, then the

spare wheel; reinstall in reverse order.

First Aid Kit

The first aid kit is located in the left

trunk well.

Stowing Things in the Vehicle

Warning!

To help avoid personal injury during

a collision or sudden maneuver,

exercise care when stowing things.

Put luggage or cargo in the trunk if

possible. Do not pile luggage or cargo

higher than the seat backs.

Vehicle Tools

The vehicle tools are located below the

jack.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands