Mercedes-Benz SL 320 Operator'S Manual Download Page 56

Page: 56 / 161

Adjusting knob

Instrument Lamps

Rotate adjusting knob (1) to vary

intensity of instrument lamps.

Display Illumination

Press adjusting knob to briefly

illuminate the display (with key

removed or in steering lock position 0

or 1).

With exterior lamps switched on the

display illumination becomes

automatically dim.

Rotate adjusting knob clockwise to its

slop to override the dimmed

illumination.

Trip odometer

To reset:

•

Press adjusting knob (1) once

(with key in steering lock

position 2).

•

Press adjusting knob (1) twice

(with key removed or in

lock position 0 or 1).

Clock

Adjusting clock one minute ahead or

back:

Pull out adjustment knob (2)

briefly

turn to the right respectively left and

release knob.

Adjusting clock more than one minute

ahead or back: Pull out adjustment

knob (2), turn to the right respectively

left and hold until the desired time is

set. Within the first 2 seconds, the

minute hand advances 8 minutes and

advances another 8 minutes every

additional second thereafter.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands