Mercedes-Benz SL 320 Operator'S Manual Download Page 139

Page: 139 / 161

139

Vehicle Data Card

The vehicle data card contains all

important data pertaining to the

vehicle. It should be kept in the

maintenance booklet where indicated,

and it is needed when obtaining

replacement or additional keys at your

authorized Mercedes-Benz dealer.

Warranty Coverage

Your car is covered under the terms of

the "warranties" printed in the Owner's

Service and Warranty Policy Booklet

and your authorized MERCEDES-

BENZ dealer will exchange or repair

any defective parts in accordance with

the terms of the following warranties:

1. New vehicle limited warranty

2. Emission systems warranty

3. Emission performance warranty

4. California emission control

systems warranty.

Loss of Owner's Service and

Warranty Policy

Should you lose your Owner's Service

and Warranty Policy Booklet, have

your authorized MERCEDES-BENZ

dealer arrange for a replacement. It will

be mailed to you.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands