Mercedes-Benz SL 320 Operator'S Manual Download Page 124

Page: 124 / 161

124

All except AMG version

Towing the Vehicle

The rear towing eye is located at the

right, below the bumper. The front

towing eye is located on the passenger

side behind a flap in the bumper panel.

Cover removal for all except AMG

version: Insert finger in recess of cover

and pull cover out.

Cover removal for AMG version: Pull

cover away from bumper.

AMG version

Cover installation for all except

AMG version: Engage cover at

bottom and press in top securely.

Cover installation for AMG version:

Engage right end of cover and press in

left end of cover.

We recommend that the vehicle be

transported using flat bed equipment.

This method is preferable to other

types of towing.

The vehicle may be towed with all of

the wheels on the ground and the

selector lever in position "N" for

distances up to 30 miles (50 km) and

at a speed not to exceed 30 mph (50

km/h).

To positively avoid a possibility of

damage to the transmission, however,

we recommend to disconnect the drive

shaft at the rear axle drive flange on

any towing beyond a short tow to a

nearby garage.

Do not tow with sling-type equipment.

Towing with sling-type equipment

over bumpy roads will damage

radiator and supports.

The use of wheel lift equipment will

damage engine oil pan.

Important!

When transporting vehicle on flat bed

equipment, the front end of the vehicle

must be loaded first. Additional

ramping may be required for loading

to protect bumper fascia.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands