Mercedes-Benz SL 320 Operator'S Manual Download Page 41

Page: 41 / 161

Latch plate

Buckle

Release button

Fastening of Seat Belts

Pull belt with latch plate (1) across

shoulder and lap. Push latch plate (1)

into buckle (2) until it clicks. The lap

belt should be positioned as low as

possible on your hips and not across

the abdomen. Do not twist the belt. A

twisted seat belt may cause injury.

For safety reasons, avoid adjusting the

seat or seat back into positions which

could affect the correct seat belt

position.

Press switch (4) to adjust seat belt so

that the shoulder portion is located as

close as possible to the middle of your

shoulder.

The shoulder portion of the seat belt

must be pulled snug and checked for

snugness immediately after engaging it

and during driving. Tighten the lap

portion to a snug fit by pulling

shoulder portion up.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands