Mercedes-Benz SL 320 Operator'S Manual Download Page 131

Page: 131 / 161

131

Replacing Wiper Blades

For safety reasons, remove key

from steering lock before replacing

wiper blade, otherwise the motor can

suddenly turn on and cause injury.

Windshield Wiper Blade

Removal:

Fold wiper arm forward. Press safety

tab down (1), push wiper blade

downward (2) and remove.

Installation:

Press down safety tab of new wiper

blade. Insert wiper blade between the

tabs (3) on the wiper arm. Then press

safety tab upward until it locks in

place.

Note:

Do not open engine hood with wiper

arm folded forward.

Do not allow the wiper arm to contact

the windshield glass without a wiper

blade inserted. The glass may be

scratched or broken.

Make certain that the wiper blade is

properly installed. An improperly

installed blade may cause windshield

damage.

Headlamp Wiper Blades

(except xenon lamps)

Removal:

Fold wiper arm forward. Press safety

tab (1) down and remove wiper blade

at guide pin (2, arrow).

Installation:

Press safety tab (1) down and insert the

guide pin (2) into the wiper arm.

Release safety tab, the wiper blade

engages.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands