Mercedes-Benz SL 320 Operator'S Manual Download Page 121

Page: 121 / 161

121

Horizontal headlamp aim

(low beams on):

Turn adjusting screw (1)

(Right front headlamp:

counterclockwise to adjust to

the left, clockwise to the

right; left front headlamp:

counterclockwise to adjust to

the right, clockwise to the

left.) until the headlamps

(low beam) illuminate the

test screen as shown. The

vertex of the angle formed in

each beam image should

align with the vertical

centerline (8) of each lamp.

The left and right headlamps must

be adjusted individually.

The indicator (7) in the sight

glass should align with the "0"

mark after any horizontal

adjustment. If it does not, insert

and turn screw driver on

adjuster (3) until scale (7) is

centered on the"0" mark.

Graduations: 0.38° pitch.

Reinstall access cover (4).

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands