Mercedes-Benz SL 320 Operator'S Manual Download Page 117

Page: 117 / 161

117

Replacing Bulbs

When replacing bulbs, install only 12

volt bulbs with the specified watt

rating.

When replacing halogen bulbs do not

touch glass portion of bulb with bare

hands. Use plain paper or a clean cloth.

Warning!

Halogen lamps contain pressurized

gas. A bulb can explode if you

•

touch or move it when hot,

•

drop the bulb,

•

scratch the bulb.

Bulb for High and Low Beam

(Halogen type 9004)

Open hood.

Squeeze latches (4) and remove cover

(3) upwards. Pull off electrical

connector (6). Turn clamping ring (7)

counterclockwise and pull out bulb

together with clamping ring. Remove

bulb.

Insert new bulb (flat side facing up),

mount clamping ring (7) (with tab

facing down) and turn clockwise. Push

electrical connector on securely.

Turn Signal, Parking, Side

Marker and Standing Lamp

(2375 NA [28.5/8.3 W/ 30/2.2

cp] bulb)

Open hood.

Turn bulb socket (5) with bulb

counterclockwise and pull out. Push

bulb into socket, turn counterclockwise

and remove.

Insert new bulb in socket, push in and

twist clockwise. Reinstall bulb socket,

push in and twist clockwise.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands