Mercedes-Benz SL 320 Operator'S Manual Download Page 97

Page: 97 / 161

Adaptive Damping System

(ADS)

Depending upon road surface

conditions, load, driving style, ADS

will automatically adjust the optimal

ride firmness.

The indicator lamp comes on with the

key in steering lock position 2 and goes

out when the engine is running.

If the indicator lamp stays on after the

engine is running or comes on while

driving, then the system has detected a

malfunction.

We recommend that you visit an

authorized Mercedes-Benz dealer as

soon as possible to have the system

checked-out.

Note:

If the battery was disconnected, the

indicator lamp will only go out after the

engine is started and the steering wheel

is turned from full left to full right lock

and returned to the center position.

Adaptive Damping System

Adjustment

The switch is located in the center

console.

Firm dampening program.

This setting should be used for

sporty driving.

During the setting for sporty

driving the indicator lamp in the

switch lights up.

Soft dampening program.

This setting should be used for

regular driving.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands