Mercedes-Benz SL 320 Operator'S Manual Download Page 126

Page: 126 / 161

126

Important!

3. Clamp one end of the first

jumper cable to the positive (+)

terminal of the discharged battery

and the other end to the positive

(+) terminal of the charged battery.

Make sure the cable clamps do not

touch any other metal parts.

4. Clamp one end of the second

jumper cable to the grounded

negative (-) terminal of the

charged battery and the final

connection to the negative (-)

terminal of the discharged

battery.

Important!

5. Start engine of the vehicle with

the charged battery arid run at

high idle". Make sure the jumper

cables are not near pulleys,

fans, or other parts that will

move when the engine is

started. Then start engine of the

disabled vehicle in the usual

manner.

6. After the engine has started,

remove jumper cables by exactly

reversing the above installation

sequence, starting with the last

connection made first. When

removing each clamp, make sure

that it does not touch any other

metal while the other end is still

attached.

Important!

A discharged battery can freeze at

approx. + 14°F (-10°C). In that case, it

must be thawed out before jumper

cables are used. A frozen battery can

explode and cause personal injury.

Jumper cable specifications:

•

Minimum cable cross-section of

25 mm

or approx. 2 AWG

•

Maximum length of 3500 mm

(11.5ft).

Manual Release of Fuel Filler Flap

In case of malfunction, the fuel filler

flap can be opened manually. Pull the

manual release knob (1) behind the

right trunk panel while simultaneously

opening the fuel filler flap.

Ski Rack

Use only our approved ski rack to

avoid damage to the vehicle. Follow

manufacturer's installation instructions.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands