Mercedes-Benz SL 320 Operator'S Manual Download Page 86

Page: 86 / 161

Engine Oil Consumption

Engine oil consumption checks should

only be made after the break-in period.

During the break-in period, higher oil

consumption may be noticed and is

normal. Frequent driving at high

engine speeds results in increased

consumption.

Fuel Consumption Gauge

While driving, instantaneous fuel

consumption is indicated in miles per

gallon (mpg), or in Canada liters per

100 kilometers (I/100 km).

With the engine switched off, the

needle reads "0".

Due to system design, maximum

consumption is indicated at idle speed.

Tachometer

Red marking on tachometer:

Excessive engine speed.

Avoid this engine speed, as it may

result in engine damage that is not

covered by the Mercedes-Benz Limited

Warranty.

For engine protection, the fuel supply

is interrupted if the engine is operated

within the red marking.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands