Mercedes-Benz SL 320 Operator'S Manual Download Page 64

Page: 64 / 161

Hardtop

The removal or attachment of the

hardtop can be carried out by

2 persons.

Warning!

Do not place your hands between the

hardtop and the car body while the

hardtop is being locked or unlocked.

Serious personal injury may occur.

Removing Hardtop

1. Engage parking brake.

2. Open doors.

3. Disconnect plug (1) for rear

window defroster.

4. Within 10 seconds of turning

key in steering lock to position 2

(engine not running), slide soft top

switch (2) back and hold.

Please note, if soft top switch is

activated after 10 seconds have

expired, turn the key back to position 0

first before the hardtop removing

procedure can be started again at

step 4.

The unlocking procedure begins after

approx. 2 seconds:

•

The roll bar lowers.

•

The indicator lamp in the

soft top switch lights up.

•

The hardtop unlocks.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands