Mercedes-Benz SL 320 Operator'S Manual Download Page 24

Page: 24 / 161

4. Function Selection Buttons

Normal Setting

Air volume and distribution are

controlled automatically.

To select:

Press

button

(indicator lamp lights up)

To change selection:

•

Press

button

(indicator lamp of selected button

lights up). The indicator lamp for

button goes out.

•

Press button 6 (indicator lamp

lights up). The indicator lamp for

button goes out.

Defrost

Maximum heated and automatically

controlled amount of air is directed to

the windshield and side windows.

As the engine coolant temperature

increases, a higher blower stage is

automatically engaged, thereby

defrosting as quickly as possible.

Turn air volume controls 11 and 13 left

to open air outlets 12 and 14. Direct

airlets towards the side windows.

The center air outlets and the foot area

ducts are closed.

To select:

Press

button (indicator lamp

lights up).

Defogging Windows

Switch on

Switch off

Economy

The function of this setting corresponds

to the normal setting. However, because

the air conditioning compressor will

not engage (fuel savings), it is not

possible to air condition in this setting.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands