Mercedes-Benz SL 320 Operator'S Manual Download Page 76

Page: 76 / 161

Drinking and Driving

Warning!

Drinking and driving can be a very

dangerous combination. Even a small

amount of alcohol or drugs can affect

your reflexes, perceptions and

judgment. The possibility of a serious

or even fatal accident is sharply

increased when you drink and drive.

Please don't drink and drive or allow

a friend to drive when he has been

drinking.

Parking Brake

To engage, depress parking brake

pedal. With the key in steering lock

position 2, the brake warning lamp in

the instrument cluster should come on

brightly (function check for lamp).

To release the parking brake, pull

handle on instrument panel. The brake

warning lamp in the instrument cluster

should go out (also see brake warning

lamp, page 88).

Driving Off

Test the brakes briefly after driving

off. Perform this procedure only when

the road is clear of other traffic.

Warm up the engine smoothly. Do not

place full load on the engine until the

operating temperature has been

reached.

Warning!

Keep driver's foot area clear at all

times. Objects stored in this area

may impair pedal movement.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands