Mercedes-Benz SL 320 Operator'S Manual Download Page 42

Page: 42 / 161

Unfastening of Seat Belts

Push in the red button (3) in the belt

buckle (2).

Allow the retractor to completely

rewind the seat belt by guiding the

latch plate (1).

Operation:

The inertia reel stops the belt from

unwinding during sudden vehicle stops

or when quickly pulling on the belt.

The locking function of the reel may be

checked by quickly pulling on the belt.

The emergency tensioning retract-ors

tighten the fastened seat belts during

frontal and front-angled impacts

exceeding the first threshold of the

SRS (see Index).

Note:

For cleaning and care of the seat belts,

see

Cleaning and Care of the Vehicle

in Index.

Warning!

USE SEAT BELTS PROPERLY.

•

Each occupant should wear

their seat belt at all times,

because seat belts help re

duce the likelihood of and

potential severity of injuries

in accidents, including roll-

overs. "SRS" (driver airbag,

passenger airbag), "ETR"

(seat belt emergency tensioning

retractors), and knee bolsters

are designed to enhance the

protection offered to properly

belted occupants in certain

frontal impacts which exceed

preset deployment thresholds.

•

Improperly positioned seat

belts do not provide maxi

mum protection and may

cause serious injuries in

case of an accident.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands