Mercedes-Benz SL 320 Operator'S Manual Download Page 127

Page: 127 / 161

127

Testing Infrared Remote Control

Checking Batteries:

If the transmit button (1) is pressed

longer than 1 second, the battery

indicator lamp in the transmitter eye

(2) briefly illuminates -indicating that

the batteries are in order.

Change batteries if the indicator lamp

does not come on.

Changing Batteries:

Unfold key from holder by pressing

lock button (3). Pull off battery

cover (4).

Change batteries, inserting new ones

under contact spring (5) with plus (+)

side facing up.

Press battery cover onto housing until

locked in place.

Important!

Batteries contain materials that can

harm the environment if disposed of

improperly. Recycling of batteries is

the preferred method of disposal. For

disposal, please follow manufacturer's

recommendation on battery package.

Replacement battery: Lithium, type CR

2025 or equivalent.

Synchronizing System:

The system may have to be re-

synchronized, if the transmitter is

without voltage for several minutes.

To synchronize system, aim transmitter

eye (2) at inside rear view mirror

receiver and briefly press transmit

button (1) twice. Within approx. 30

seconds, insert key in steering lock and

turn it to position 2.

The infrared remote control should

once again be operational.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands