Mercedes-Benz SL 320 Operator'S Manual Download Page 60

Page: 60 / 161

Interior Lighting

The switch is located above the inside

rear view mirror.

Interior Lamp

Interior lamps are switched on,

and off delayed, when unlocking or

locking the vehicle, or when

opening either door.

However, there will be no delay

when the key is in steering lock

position 2.

Interior lamps switched off.

Interior lamps switched on

continuously.

Reading Lamps

Left reading lamp switched on,

Reading lamps switched off.

Right reading lamp switched on.

Entrance Lamps, Exit Lamps

Entrance lamps are located in the

footwells under the dashboard.

Exit lamps are located in the door

pockets.

These lamps are switched on and off

by the door contact switches.

Note:

To prevent the vehicle battery from

being discharged, do not leave doors

open for a long period of time.

Summary of Contents for SL 320


































































































































































Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands

Mercedes-Benz SL 320, Operator'S Manual

Search results

Summary of Contents for SL 320

Reviews:

Related manuals for SL 320

Brands by name

Popular brands