manualshive.com logo in svg

MCK EXTender 7000, Installation Manual

The MCK EXTender 7000 is an innovative device designed to extend the range of your Wi-Fi network effortlessly. For a trouble-free installation, refer to our comprehensive Installation Manual available for free download at manualshive.com. This manual provides step-by-step instructions to ensure a seamless setup process for your convenience.

Share
Download
background image

EXTender

TM 

7000 Installation Guide                                                                                                                                                     

Page 78

RVP_Direct Settings

MI Path 

Configuration -> Connect -> RVP_Direct

12. Primary Interface: T1_Port1_Leased
13. EXTender BW: Bandwidth required for EXTended phones.

Local Dialing via PRI

Note: In this application, the network between the GII and EXT 7000 is a T1.

MI Path 

Configuration -> WAN -> T1/PRI_Port (WAN3)-> T1/PRI_Port_2

Procedure:

1.

Enabled: Yes

2.

Mode: PRI

3.

Node Type: User

4.

Switch Type: Value provided by Telco.

5.

Line Code: Value provided by Telco.

6.

Framing: Value provided by Telco.

7.

Line Build Out: 0db or as specified by the Telco.

8.

Caller ID: See the EXTender 7000 User’s Guide for instructions on configuring Caller ID.

Figure 5-29: T1/PRI Port 2

Setting the DSO Default Parameters

MI Path:

Configuration -> WAN -> T1/PRI_Port (WAN3)-> T1/PRI_Port_2 ->Channel Setup-> 

DS0_Default

Note: These “Default” port settings will set all channels identically.

1.

Enabled: Yes

2.

Direction: Both

3.

Services: 80 (to assign PRI voice services to all DS0 channels, or 83 (for DEFINITY)

4.

Connect Type: Dialup

5.

DS0 DN: N/A

MI Path 

Configuration -> Connect -> RVP_Direct

6.

Primary Interface: T1_Port1_Leased

7.

EXTender BW: Total voice Bandwidth

Summary of Contents for EXTender 7000






















































































Reviews:

No comments

Related manuals for EXTender 7000

Panasonic KX-TDA15 User Manual preview
KX-TDA15
Brand: Panasonic Pages: 202

Brands by name

Popular brands

Load more brands