manualshive.com logo in svg

MCK EXTender 7000, Installation Manual

The MCK EXTender 7000 is an innovative device designed to extend the range of your Wi-Fi network effortlessly. For a trouble-free installation, refer to our comprehensive Installation Manual available for free download at manualshive.com. This manual provides step-by-step instructions to ensure a seamless setup process for your convenience.

Share
Download
background image

EXTender

TM 

7000 Installation Guide                                                                                                                                      

Page 4

Table of Contents

Copyright Information ................................................................................................................................. 3

Table of Contents ........................................................................................................................................ 4

Chapter 1:Introduction ............................................................................... 7

Purpose of this Document .......................................................................................................................... 7

Related Documentation  ..............................................................................................................................7
Naming Conventions  ..................................................................................................................................7

Safety Considerations................................................................................................................................. 8

Service ........................................................................................................................................................8

Specifications .............................................................................................................................................. 9

Regulatory Approvals  .................................................................................................................................9
System Architecture  ...................................................................................................................................9
Memory .......................................................................................................................................................9
WAN Ports ..................................................................................................................................................9

WAN 1 and WAN 2  .................................................................................................................................9
Internal MCK WAN Card  .........................................................................................................................9

Interfaces ..................................................................................................................................................10
Voice Protocols and Services ...................................................................................................................10
Electrical ...................................................................................................................................................10
Mechanical ...............................................................................................................................................10
Environmental ...........................................................................................................................................10

Chapter 2:Connection and Wiring .......................................................... 13

Prerequisites for Installation .................................................................................................................... 14

Network Requirements  .............................................................................................................................14
Space Requirements  ................................................................................................................................14

Supported Telephones.............................................................................................................................. 15

RemoteConneX Phones ...........................................................................................................................15
Avaya Definity ...........................................................................................................................................15
Nortel Meridian  .........................................................................................................................................15
Nortel Norstar  ...........................................................................................................................................15

EXTender Parts for Installation ................................................................................................................ 16

Parts Provided with the EXTender  ...........................................................................................................16
Parts Not Provided with the EXTender .....................................................................................................16
Installation Considerations  .......................................................................................................................16

Mounting and Connections for the EXTender 7000 ............................................................................... 17

Connections to the EXTender 7000  .........................................................................................................17

Telephony Wiring (RJ-21) ......................................................................................................................... 19

Serial Console Connection and Setup..................................................................................................... 20

Required Cable .........................................................................................................................................20
Enhanced Terminal Interface (ETI) Setup  ................................................................................................20

Power-Up .................................................................................................................................................... 22

The Management Interface ....................................................................................................................... 23

Set Up Wizard............................................................................................................................................. 24

Standard Console UI vs. the Setup Wizard ...........................................................................................24

Chapter 3:Configuration  .......................................................................... 25

RVP_Direct via Leased T1 Line Configuration........................................................................................ 26

Installation .............................................................................................................................................26

Summary of Contents for EXTender 7000






















































































Reviews:

No comments

Related manuals for EXTender 7000

Yeastar Technology S-Series Administrator'S Manual preview
S-Series
Brand: Yeastar Technology Pages: 128
ATCOM IPPBX IP08 Product Manual preview
IPPBX IP08
Brand: ATCOM Pages: 64
Panasonic KX-TDA100AL Service Manual preview
KX-TDA100AL
Brand: Panasonic Pages: 125
Telco Depot TD100 SERIES User Manual preview
TD100 SERIES
Brand: Telco Depot Pages: 71

Brands by name

Popular brands

Load more brands