Leica EM ACE600 Operating Manual Download Page 67

Page: 67 / 132

Operating Manual Leica EM ACE600

Version 01/19

Page 62

Grid stage and standard stage with a diameter of 60 mm:

Standard stage and quartz holder mounted on the EM ACE600

After choosing and starting a protocol for e-beam evaporation the system will
perform the following steps automatically (see 3.9.2 and 3.9.3).



Pumping



Pumping until base vacuum is reached



Setting the stage



Degassing the target material (if activated)



Opening the shutter and starting rotation (if activated)



Evaporating until final thickness is reached or defined time has elapsed



Closing the shutter



Displaying the results of the process, venting or staying in vacuum

Caution!

Be careful when reloading a just used e-beam source.

The inside of the source can get extremely hot.

Summary of Contents for EM ACE600





































































































































Search results

Summary of Contents for EM ACE600

Reviews:

Related manuals for EM ACE600

Brands by name

Popular brands

Leica EM ACE600, Operating Manual

Search results

Summary of Contents for EM ACE600

Reviews:

Related manuals for EM ACE600

Brands by name

Popular brands