Leica EM ACE600 Operating Manual Download Page 117 | Manualshive

Page: 117 / 132

background image

Operating Manual Leica EM ACE600

Version 01/19

Page 112

Cleaning material

There is a Leica cleaning product available for parts used in vacuum, which is the
ideal solution for cleaning: 16771511205.

If not by hand, alternatively, metal cleaning paste works well. Scotch brite should
only be used on metal parts. Do not use any abrasives on the glass door because
scratches can lead to small leaks. Washing the parts afterwards with soapy water
and letting them dry off is an easy way to finish the cleaning. In addition,
Isopropanol or Ethanol can be used for the finish.

Caution!
Do not use thin tissues and ethanol for removing platinum – there is a risk
of the tissue catching fire.

Door



Remove the door by lifting it from its hinges (see 4.2.1)



Place the door on a flat soft surface with the inner surface up



To remove carbon coatings, use a 70% isopropanol solution and lint-free

tissue for the rough cleaning. Then use fine metal polish paste. Finish with
soap-water or isopropanol



To remove sputter coatings, start with the fine polish paste and finish with

soap-water or isopropanol

«
...
115
116
117
118
119
...
»

Summary of Contents for EM ACE600





































































































































Reviews:

No comments

Related manuals for EM ACE600

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: Abicor Binzel Pages: 92

Brand: Handler Pages: 25

Brand: Faderfox Pages: 8

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: RainPoint Pages: 40

Brand: FARM-MAXX Pages: 35

Brand: Sota Pages: 7

Brand: Lumineux Pages: 2

Zen-O lite RS-00600

Brand: GCE Pages: 20

Brand: MadLab Pages: 7

Brand: Garmin Pages: 41

Brand: Cuisinart Pages: 159

DJ Laptop stand +tray

Brand: Power Dynamics Pages: 3

Brand: Kobelt Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands