Leica EM ACE600 Operating Manual Download Page 126

Page: 126 / 132

Operating Manual Leica EM ACE600

Version 01/19

Page 121

E2003

Process

Process terminated mains
supply voltage out of range
150<>210 V

Process - aborted. Mains supply
voltage out of range! (150<>210
V) Check if right voltage is
delivered by the network

E2004

Process

Process terminated, Mains
supply voltage out of range
>250 V

Process stop. Mains supply
voltage out of range! (>250 V)
Check if right voltage is delivered
by the network

E2005

Process

Process terminated, Current
not reached, Check target
and sputter source

Process aborted - Unable to reach
sputter-current. Check if pressure
is valid or wrong or no target is
used.

E2007

Process

Process terminated, Line
voltage fluctuations

Process aborted - Line voltage
fluctuations too big!

E2009

Process

Process terminated, Sputter
source short circuit! Check
target and sputter source.

Process aborted - Short-circuit
because of invalid assembly of
head, ring or target. Check
deposited solid material on shutter

E2010

Process

Process terminated, ignition
fault, Check argon flow,
Check target and sputter
source

Process aborted - Unable to
establish plasma ignition.

E2011

Process

Process terminated, Sputter
current could not be
stabilized

Process aborted - Unstable
plasma current. Unclean target
could be the reason, clean with
isopropanol and try again.

E2012

Process

Process terminated, High
voltage board defect, please
contact service

Process aborted - High voltage
board defect > Change board,
since output cannot be controlled
anymore

E2018

Process

Operation Response Timeout

The control unit cannot stabilize
the voltage in the sputter head.

W2019

Warning

Purge Base-Vacuum (1.0E-4
Mbar) Timeout. Process
Anyway?

Begin Sputter using Standby
Mode

Glow discharge specific:

E2109

Process

Process terminated, Short
circuit in glow-discharge,
Check shutter panels

Process aborted - Short-circuit
because of invalid assembly of
plates. Check deposited solid
material on shutter

Summary of Contents for EM ACE600





































































































































Search results

Summary of Contents for EM ACE600

Reviews:

Related manuals for EM ACE600

Brands by name

Popular brands

Leica EM ACE600, Operating Manual

Search results

Summary of Contents for EM ACE600

Reviews:

Related manuals for EM ACE600

Brands by name

Popular brands