Leica EM ACE600 Operating Manual Download Page 123

Page: 123 / 132

Operating Manual Leica EM ACE600

Version 01/19

Page 118

W0010

Warning

Turbo temperature too high,
Service diaphragm pump

Turbo temperature over-heat. Stop
pumping and wait.

W0011

Warning

Critical disk space, Back-up
files before clean up?

Not enough memory left on
device. Clean up device > Delete
old logs, screenshots and update
folders.

E0012

Error

No pump calibration table
found, please calibrate pump
to ensure correct behaviour

No pump calibration file found.
Calibrate pump in service.

E0013

Error

No available coating method
detected, Restart system

No available coating method
controller detected. Check
communication cables and HiVac
controller status.

W0014

Warning

Service interval gauge
exceeded, Service gauge

Gauge service interval exceeded.
Reset interval in software after
service.

W0016

Warning

Gauge pressure out of
bounce, Restart system

Invalid gauge pressure value
received. Check gauge connection
or restart controller.

E0017

Error

Sudden Vacuum Break
Down; Check Valves and
Device For Leaks

Vent after the Valve, then Open
the FSA-Valve, Pressure Drop

E0018

Error

Vacuum Timeout; Check
Valves and Device For Leaks

W0019

Warning

Side Stage, Working
Distance Lower than 80 mm

HiVac Controller Specific:

W1300

Warning

No quartz detected

Quartz not detected. Warning only
active in debug mode.

Summary of Contents for EM ACE600





































































































































Search results

Summary of Contents for EM ACE600

Reviews:

Related manuals for EM ACE600

Brands by name

Popular brands

Leica EM ACE600, Operating Manual

Search results

Summary of Contents for EM ACE600

Reviews:

Related manuals for EM ACE600

Brands by name

Popular brands