Leica EM ACE600 Operating Manual Download Page 56 | Manualshive

Page: 56 / 132

background image

Operating Manual Leica EM ACE600

Version 01/19

Page 51

4.6.2 Choosing a carbon thread protocol

When the head is inserted after completing the preparation in 4.6.1 an
evaporation process can be run. Select carbon thread on the first screen to enter
the process screen. In the library of recipes (1) all stored protocols are available
and can be chosen. Tapping on the characteristics of the protocol (2), opens the
list of recipes. There, the parameters for the process can be changed and saved.
Thickness or pulses/flashes can be adjusted on the process screen (3). Once
everything relevant for the coating process is defined, the process can be started
(4).

Select a protocol by tapping on it. Once it is marked, by tapping on a specific
category, the parameters can be changed. Alternatively, a protocol can be copied
and then modified or a new one added.

1

2

3

4

«
...
54
55
56
57
58
...
»

Summary of Contents for EM ACE600





































































































































Reviews:

No comments

Related manuals for EM ACE600

Brand: Navman Pages: 17

Brand: GE Pages: 14

Brand: GE Pages: 11

Brand: GE Pages: 20

Druck ADTS 2 Series

Brand: GE Pages: 18

Brand: Cadex Pages: 300

Brand: made for movement Pages: 51

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: iFIT Pages: 11

Brand: iHealth Pages: 8

Brand: Keller Pages: 12

Brand: MacDon Pages: 49

Brand: MacDon Pages: 49

Brand: MacDon Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands