Leica EM ACE600 Operating Manual Download Page 26 | Manualshive

Page: 26 / 132

background image

Operating Manual Leica EM ACE600

Version 01/19

Page 21

For sputtering process only:
Connect to argon gas (supplied hose, 6 mm diameter). Purge argon line before
connecting to remove the air from inside the hose. This can help to reduce the
pump down time. Regulate argon pressure to ~0.5 bar over atmosphere.

We strongly recommend using a two-stage pressure regulator on the argon
bottle.

«
...
24
25
26
27
28
...
»

Summary of Contents for EM ACE600





































































































































Reviews:

No comments

Related manuals for EM ACE600

Brand: Garelick Pages: 2

Brand: Gardico Pages: 2

Brand: OceanSat Pages: 85

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: HANYOUNG NUX Pages: 2

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: Park Tool Pages: 4

Brand: Qlight Pages: 4

Brand: U-Line Pages: 9

Green Machine H-3518

Brand: U-Line Pages: 3

Brand: RAMVAC Pages: 53

Brand: Waves Pages: 8

Brand: Alpina Pages: 24

Brand: Bird-X Pages: 2

Brand: Lightolier Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands