Lauda PROLINE Edition X P 12 C, Operating Instructions Manual

Page: 36 / 116

Proline Edition X heating thermostats
36
Starting up
YACE0099 / 10/9/2018
7.5 Menu structure: "Master"
2 dots in the display, e.g.
MNEmv
, indicate
that a submenu follows.
3 dots in the display, e.g.
MNpfv
, indicate
that a module submenu follows.
UEr Software version
Section 9.2.2
Snr_H Serial number Hi Word.
Section 9.2.3
Snr_L Serial number Lo Word.
Section 9.2.3
StELL
Control val. of temp.
controller. Section 9.2.4
tHEAd Temp. of housing °C
Section 9.2.4
tHS Temp. of heatsink °C
Section 9.2.4
FAn U Fan voltage V
Section 9.2.4
1EFF Mains curr. consumpt. A
Section 9.2.4
U_SEC Prot.syst. volt. V
Section 9.2.4
U24 Act. val. 24V volt. V
Section 9.2.4
PU 1 Current consumpt. pump I
Section 9.2.4
PU P Power consumpt. pump W
Section 9.2.4
PU n Pump speed rpm
Section 9.2.4
nF 50 Mains frequency Hz
Section 9.2.4
nU Mains volt. % of rated volt.
Section 9.2.4
LE Bath level [cm]
Section 9.2.4
tE Pt Extern temp. Pt100
Section 9.2.4
tEAnA Ext.temp. analog interf.
Section 9.2.4
tESEr Ext.temp. RS-232/485
Section 9.2.4
iSEt Curr. controller setpoint.
Section 9.2.4
H_PU counter operating hours
pump.
H_All counter operating hours
Master complete.
SEt Set setpoint
Section 7.7.1
Pu Pump power
Section 7.7.3
Con Control Int/Ext
Section 7.7.4
MNEmv
Settings
MNpfv Conf. Modules
SED.. Protection system
C0MN Command
VAQ Solenoid valve

3
AnA Analog module

8.4
rS Conf. RS-232/485

8.3
d1b Conf. contact mod.

8.5
PArA Parameters
P1d.. Control paramet.
Only internal or external
parameters are offered
depending on control
variable
ShoZ\ Show values
CAL.. Pt100 calibration
dEF Works settings
Section 7.13.1
_P Int. proport.range (Xp)
Section 7.13.1
tn Int. reset time(Tn)
Section 7.13.1
tud Int. contr. par. auto/man.
Section 7.13.1
CAL 1 Offset int. Pt100
Section 7.8.7
dEF ! Works settgs. int. Pt
Section 7.8.8
CAL E Offset ext. Pt100
Section 7.8.9
dEF E Works settgs. ext. Pt
Section 7.8.10
SEtq. Setpoint relat.to act.
val. Section 7.8.4
S Setpoint resolution
Section 7.8.1
StArt Opern. w. mains fail.
Section 7.8.2
tih Upper temp. limit
Section 7.8.3
Cur Max. current consumpt.
Section 0
tiL Lower temp. limit
Section 7.8.3
tYPG. Detect type of unit.
Section 9.2.1
dEF Works setting
Section 7.8.5
Audjp Signal settings.
Section 7.8.6
2%32
Actual bath temperature
or actual value of exter-
nal temperature
E Ext. contr. par. auto/ man.
Section 7.13.2
EP Ext.prop.factor (Kpe)
Section 7.13.2
En Ext.reset time (Tne)
Section 7.13.2
iP Ext.proport. range (Xpf)
Section 7.13.2
dEF Works settings
Section 7.13.2
Et0L Ext.correct. var. (K)
Section 7.13.2