Lapis ML610Q111 User Manual Download | Manualshive

Page: 290 / 402

background image

ML610Q111/ML610Q112 User’s Manual

Chapter 16 Port B

FEUL610Q111

16-11

16.3 Description of Operation

16.3.1 Input/Output Port Functions

For each pin of Port B, either output or input is selected by setting the Port B direction register (PBDIR).
In output mode, high-impedance output mode, P-channel open drain output mode, N-channel open drain output mode, or
CMOS output mode can be selected by setting the Port B control registers 0 and 1 (PBCON0 and PBCON1).
In input mode, high-impedance input mode, input mode with a pull-down resistor, or input mode with a pull-up resistor can
be selected by setting the Port B control registers 0 and 1 (PBCON0 and PBCON1).
At a system reset, high-impedance output mode is selected as the initial state.
In output mode, “L” or “H” level is output to each pin of Port B depending on the value set by the Port B data register
(PBD).
In input mode, the input level of each pin of Port B can be read from the Port B data register (PBD).

16.3.2 Primary Function except for Input/Output Port

Port B is assigned to the SA A/D converter input pins(AIN2-5), Analog comparator input(CMP0M, CMP0P), External
interrupts(EXI4-7), Trigger inputs(TETG, TFTG, PCTG, PDTG, PETG, PFTG), UART input pins (RXD0, RXD1) as
primary function except for input/output port.
When used as the SA A/D converter input pins (AIN2-5) and Analog comparator input(CMP0M, CMP0P), set an
applicable port as a high impedance output state.
When used as the External interrupts/Trigger inputs /UART input pins (EXI4-7, TETG, TFTG, PCTG, PDTG, PETG,
PFTG, RXD0, RXD1), set an applicable port as a input state.

16.3.3 Secondary tertiary and fourthly functions

Port B is assigned to PWM output pins (PWMC, PWMD, PWME, PWMF0, PWMF1, PWMF2), comparator output pin
(CMP1OUT), SSIO pins (SIN, SOUT, SCK), UART output pins (TXD0, TXD1), I

2

C pins (SCL, SDA), external clock pin

(CLKIN), clock output pins (OUTCLK, LSCLK) as its secondary, tertiary and fourthly functions. These pins can be used in
secondary, tertiary and fourthly functions mode by setting the PB7MD0 to PB0MD0 bits and the PB7MD1 to PB0MD1
bits of the Port B mode registers (PBMOD0, PBMOD1).

«
...
288
289
290
291
292
...
»

Summary of Contents for ML610Q111



















































































































































































































































































































































































































Reviews:

No comments

Related manuals for ML610Q111

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands