manualshive.com logo in svg

Kwik Lok 893A ULTRA, Instruction Manual

Share
Download
Kwik Lok 893A ULTRA Instruction Manual Download Page 106

Appendix

P 6

893 05 15

NOTE:

Specify on the order the TYPE, MODEL,

and SERIAL NUMBER of the machine for which

the parts are ordered.  This information will be

found on the machine’s nameplate.

CONTACT THE FACTORY FOR

CURRENT PRICES.

SUGGESTED SPARE PARTS INVENTORY FOR THE

TYPE 893 CLOSER

Part no.

Description

Qty.

Part no.

Description

Qty.

EXECUTIVE OFFICE P.O. BOX 9548  YAKIMA, WA.  98909  

TELEPHONE: 1-800-688-5945 or  (509) 248-4770

FAX: (509) 457-6531

Internet: www.kwiklok.com

CORPORATION

®

®

00-001374

Belt-Upper Idle

2

00-001375

Belt-Lower Idle

2

08-006007

Gear - Nylon

1

08-006019

Motor - Stepper

1

08-006036

Sensor-Barrel

1

08-006957

Filter - Fan

2

Z8093030

Solenoid - Lok Check

1

Underlined part numbers indicate the suggested 

minimum inventory.

Z0088015

Pulley Assembly (Smooth)

4

Z0088010

Pulley Assembly (Tooth)

4

0S-128

Spring

2

P03-00143

Belt - Gear

4

P10-00111

Power Supply

1

P10-00112

DC Converter

1

P23-00331

Screw

2

Kwik Lok

WARRANTY POLICY

Seller warrants that the equipment shall be free of defective workmanship or materials. Its obligation under this

warranty to consist exclusively of repairing or replacing, free of charge EXW, any parts received at its factory

within two years from the date of shipment of the respective equipment or parts alleged to be defective and

determined by Seller upon inspection to be defective.  

No other warranty, expressed or implied, as to description, quality, merchantability, fitness for a particular 

purpose or any other matter is given by Seller in connection with this sale. Under no circumstances shall Seller

be liable for loss or profits or other consequential damages, or for any other direct or indirect costs, expenses, 

equipment or any part thereof.  Neither shall the Seller be liable for any defects attributable to the use of any

parts, supplies or service not manufactured, supplied or provided by the Seller.

Electric motors, controls and electronic components carry a one year warranty in which these items will be

repaired or replaced and returned to the Buyer at no charge if the manufacturer determines the equipment to

be defective in workmanship and / or materials. The disassembly of motors, gear-motors and clutches will void

the aforementioned warranty.

Summary of Contents for 893A ULTRA











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands