Julabo Presto Series Operating Manual Download Page 65

Page: 65 / 121

USER INTERFACE

2.13.2018

10.5. "Analog interfaces" menu

Select menu

The buttons will display the current
settings.

indicates available submenu



If the electronic module has not been installed, the key

>Analog Module< will not be displayed in this menu.

10.5.1. Alarm output

The buttons will display the current
settings.

Breaking capacity

max. 30 W / 25 VA

with turn-on voltage

max. 30 V

; max. 25 V

with switching current

max. 1 A

Socket on the front

Alarm output: Output for external alarm signal.
This contact is a potential-free change-over contact. All of the unit's

operating conditions can be sent externally via settings in the

>Alarm output< menu without modifying the plug connection.

Setting

Standby

Alarm

Alarm+Stdby

Pump on

connects pins

2 and 3.
Setting

Standby / Inverted

Alarm / Inverted

Alarm+Stdby /

Inverted

Pump on / Inverted

connects pins 2 and 1.

Summary of Contents for Presto Series


























































































































Search results

Summary of Contents for Presto Series

Reviews:

Julabo Presto Series, Operating Manual, Page: 65 / 121

Search results

Summary of Contents for Presto Series

Reviews: