Julabo Presto Series Operating Manual Download Page 114

Page: 114 / 121

Error messages

114

2.13.2018

Alarm-Code

Cause

Diagnosis / Remedy

E506

Invalid flow value during flow regulation. The calculated flow value is invalid for

the flow regulator, or the function of the

external sensor connection "JULABO

Sensor Pressure/Flow" not set to the

Flow setting.

Please deactivate flow regulation, or

switch the function of the external sensor

connection to Flow.

E507

Invalid setpoint calculation in internal

program sensor.

Please restart the profile.

E508

Invalid setpoint was received on the

internal bus.

Please set a valid setpoint.

E509

Invalid setpoint should be send on the

internal bus.

Please set a valid setpoint.

E510

Current measurement at the "JULABO

Sensor Pres./Flow" sensor input

incorrect.

Check the sensor and the menu settings

for the sensor input "JULABO Sensor

Pressure/Flow".

E513

Flow rate control via external bypass

activated, but external bypass is not

recognized.

Connect an external bypass to the system or

change the type of pump control.

Summary of Contents for Presto Series


























































































































Search results

Summary of Contents for Presto Series

Reviews:

Julabo Presto Series, Operating Manual, Page: 114 / 121

Search results

Summary of Contents for Presto Series

Reviews: