manualshive.com logo in svg

Julabo Presto Series, Operating Manual, Page: 111 / 121

Share
Download
Julabo Presto Series Operating Manual Download Page 111

USER INTERFACE 

2.13.2018

 

 

111 

Alarm-Code 

Cause  

Diagnosis / Remedy 

 

E116 

The relay lock of the safety mechanism is 

still active. 

The unit was turned back on too quickly to 

reset the relay lock of the safety 

mechanism. 
Turn off the unit at the power switch, wait 4 

seconds, and turn the unit back on. 

 

E117 

Local overheating at heater. 

(1) The viscosity of the liquid may not 

exceed the maximum permitted value at any 

working temperature. 
(2) The medium has not been completely 

purged. 
(3) There is too less recirculation. 

 

E118 

Error in internal temperature measurement 

circuit. 

If this error continues to occur, please 

contact JULABO Service. 

 

E119 

Line break in external temperature probe 2. 

Check the electrical connection to external 

temperature probe 2 (EXT Pt100 2). 

 

E120 

Short circuit in external temperature probe 

2. 

Check the electrical connection to external 

temperature probe 2 (EXT Pt100 2). 

 

E201 

Error in pump pressure measurement. 

If this error continues to occur, please 

contact JULABO Service. 

 

E201 

Error in cooling water pressure 

measurement. 

If this error continues to occur, please 

contact JULABO Service. 

 

E204 

Error in total current measurement. 

If this error continues to occur, please 

contact JULABO Service. 

 

E204 

Error in current measurement in heater 

circuit. 

If this error continues to occur, please 

contact JULABO Service. 

 

E205 

Error in current measurement for compressor 

stage 1. 

If this error continues to occur, please 

contact JULABO Service. 

 

E206 

Error in current measurement for compressor 

stage 2. 

If this error continues to occur, please 

contact JULABO Service. 

 

E207 

Error in current measurement in pump 

circuit. 

If this error continues to occur, please 

contact JULABO Service. 

 

E208 

Error in main power voltage measurement. 

If this error continues to occur, please 

contact JULABO Service. 

 

E301 

The pressure in the external temperature 

control circuit has been higher than the peak 

limit entered for 1 second. 

Correct the pressure setpoint downwards, or 

set the peak pressure limit upwards (if 

reasonable from a safety standpoint). 

 

E302 

The pressure in the external temperature 

control circuit has been higher than the limit 

entered for 5 seconds. 

Correct the pressure setpoint downwards, or 

adjust the pressure limit upwards (if 

reasonable from a safety standpoint). 

 

E303 

Fuse SI2 or SI3 on the power module is 

defective. 

The power module or the fuse must be 

replaced. 
 

 

E304 

Main power voltage is detected even though 

the unit is in standby mode. 

If this error continues to occur, please 

contact JULABO Service. 

 

E401 

Evaporator outlet temperature probe is 

defective. 

Evaporator outlet temperature probe is short-

circuited. 

 

E402 

Evaporator outlet temperature probe is 

defective. 

Line break to evaporator outlet temperature 

probe. 

Summary of Contents for Presto Series


























































































































Reviews:

No comments