Julabo Presto Series Operating Manual Download Page 115

Page: 115 / 121

USER INTERFACE

2.13.2018

115

15.2.

Warning messages

Alarm-Code

Cause

Diagnosis / Remedy

E03

Overtemperature limit exceeded during

operation.

The temperature measured is above the

overheating limit. Please raise the

overheating limit, or lower the temperature

setpoint.

E04

Subtemperature limit violated during

operation.

The temperature measured is below the

configured subtemperature limit. Please

lower the subtemperature limit, or increase

the temperature setpoint.

E40

The early warning system for low liquid level

is indicating a critical liquid level.

Please refill temperature control liquid.

E41

The early warning system for high liquid

level is indicating a critical liquid level.

Please drain temperature control liquid.

E1103

Error in level detection.

If this error continues to occur, please

contact JULABO Service.

E1104

Error in level detection.

If this error continues to occur, please

contact JULABO Service.

E1107

The temperature of the heat exchanger or

the internal reservoir is near the configured

safety temperature.

Check the setting of the high temperature

cut-off.

E1108

The temperature of the heat exchanger or

the internal reservoir is near the configured

safety temperature.

Check the setting of the high temperature

cut-off.

E1109

Probe differential limit activated.

Check heat transfer medium for suitability

for use in the temperature range in use!
The viscosity of the heat transfer medium

may not exceed the maximum permitted

value at any working temperature.
Please contact JULABO Service if you have

any questions regarding JULABO heat

transfer media.

E1203

Error in pump pressure measurement.

If this error continues to occur, please

contact JULABO Service.

E1204

Error in pump pressure measurement.

If this error continues to occur, please

contact JULABO Service.

E1205

Error in cooling water flow rate

measurement.

If this error continues to occur, please

contact JULABO Service.

E1206

Error in cooling water flow rate

measurement.

If this error continues to occur, please

contact JULABO Service.

E1207

Error in total current measurement.

If this error continues to occur, please

contact JULABO Service.

E1208

The current measurement for total current is

incorrect.

If this error continues to occur, please

contact JULABO Service.

E1209

Error in current measurement for

compressor stage 1.

If this error continues to occur, please

contact JULABO Service.

Summary of Contents for Presto Series


























































































































Search results

Summary of Contents for Presto Series

Reviews:

Julabo Presto Series, Operating Manual, Page: 115 / 121

Search results

Summary of Contents for Presto Series

Reviews: