Julabo Presto Series Operating Manual Download Page 117

Page: 117 / 121

USER INTERFACE

2.13.2018

117

Alarm-Code

Cause

Diagnosis / Remedy

E1434

Cooling water temperature too high

Check cooling water.

E1435

Cooling water temperature too low

Check cooling water.

E1501

A timeout occurred on the serial interface.

If the watchdog is activated, the setpoint

must be sent to the device periodically, at

least every 30 seconds.

1502

The pressure in the temperature control

circuit is higher than the configured warning

limit

(1) Correct the pressure setpoint downwards

(2) Adjust the warning limit upwards (if

reasonable from a safety standpoint).

1503

The pressure in the temperature control

circuit is lower than the configured warning

limit

(1) Correct the pressure setpoint upwards or

(2) Adjust the warning limit downwards (if

reasonable from a safety standpoint).

1504

The flow in the temperature control circuit is

higher than the configured warning limit

(1) Correct the flow setpoint downwards or

(2) Adjust the warning limit upwards (if

reasonable from a safety standpoint).

1505

The flow in the temperature control circuit is

lower than the configured warning limit

(1) Correct the flow setpoint upwards or

(2) Adjust the warning limit downwards (if

reasonable from a safety standpoint).

Summary of Contents for Presto Series


























































































































Search results

Summary of Contents for Presto Series

Reviews:

Julabo Presto Series, Operating Manual, Page: 117 / 121

Search results

Summary of Contents for Presto Series

Reviews: