Julabo Presto Series Operating Manual Download Page 108

Page: 108 / 121

Error messages

108

2.13.2018

15. Error messages

In the following all error messages for

units, which

may occur, are listed. Due to the varying performance classes of

the units the number of displayed error messages differs. 1-stage

units do not display error messages which affect only errors of

stage 2.

For better orientation the tables are colored in correspondance with

the error messages on the TFT display.

ALARM display

Error messages are displayed in a
red box.

Press <

> for help text.

WARNING display

Warnings are displayed as a ticker

in the status line.

Legend of the tables:

Alarm-Code

Cause

Diagnosis / Remedy

E01

ode

/ N

Abbreviations used:

Safety sensor (SF0, SF1, …)

SF0_0

Safety sensor 0 in configuration 0

SF0_1

Safety sensor 0 in configuration 1

etc.

CAN

CAN-Bus (Internal bus system)

E03

Warnings with high priority

E2101

Warnings with low priority

Summary of Contents for Presto Series


























































































































Search results

Summary of Contents for Presto Series

Reviews:

Julabo Presto Series, Operating Manual, Page: 108 / 121

Search results

Summary of Contents for Presto Series

Reviews: