manualshive.com logo in svg

Julabo Presto Series, Operating Manual, Page: 112 / 121

Share
Download
Julabo Presto Series Operating Manual Download Page 112

Error messages  

112 

 

2.13.2018

 

Alarm-Code 

Cause  

Diagnosis / Remedy 

 

E403 

Compressor outlet temperature probe is 

defective. 

Compressor outlet temperature probe is 

short-circuited. 

 

E404 

Compressor outlet temperature probe is 

defective. 

Line break to compressor outlet temperature 

probe. 

 

E405 

Compressor inlet temperature probe is 

defective. 

Compressor inlet temperature probe is short-

circuited. 

 

E406 

Compressor inlet temperature probe is 

defective. 

Line break to compressor inlet temperature 

probe. 

 

E407 

Air intake temperature probe is defective 

Air intake temperature probe is short-

circuited. 

 

E408 

Air intake temperature probe is defective. 

Line break to air intake temperature probe. 

 

 

E409 

Compressor temperature probe is defective.  Compressor temperature probe is short-

circuited. 

 

E410 

Compressor temperature probe is defective.  Line break to compressor temperature 

probe. 

 

E411 

Water intake or condensation temperature 

probe is defective. 

Water intake or condensation temperature 

probe is short-circuited. 

 

E412 

Water intake or condensation temperature 

probe is defective. 

Line break to water intake or condensation 

temperature probe. 

 

E413 

Evaporation pressure sensor is defective. 

Evaporation pressure sensor is short-

circuited. 

 

E414 

Evaporation pressure sensor is defective. 

Line break to evaporation pressure sensor. 

 

E415 

Reserve pressure sensor is defective. 

Reserve pressure sensor is short-circuited. 

 

E416 

Reserve pressure sensor is defective. 

Line break to reserve pressure sensor. 

 

E417 

Condensation pressure sensor is defective. 

Condensation pressure sensor is short-

circuited. 

 

E418 

Condensation pressure sensor is defective. 

Line break to condensation pressure sensor. 

0 

E419 

One or more of the following problems has 

occurred: 

(1) Ambient temperature too high 

(2) Condenser contaminated 

(3) Cooling water temperature too high 

(4) Quantity of cooling water too low 

Please check the setup conditions, including 

the ambient and cooling water temperatures, 

and clean the condenser. 

1 

E419 

Error in Stage 1 of the cooling system. 

Please check the setup conditions, including 

the ambient and cooling water temperatures, 

and clean the condenser. 

 

E420 

Error in Stage 1 of the cooling system. 

If this error continues to occur, please 

contact JULABO Service. 

 

E421 

Ambient temperature outside specifications. 

Please check the ambient temperature and 

clean the condenser. 

 

E422 

Ambient temperature outside specifications. 

Please check the ambient temperature and 

clean the condenser. 

 

E425 

Error in cooling system. 

If this error continues to occur, please 

contact JULABO Service. 

 

E426 

Error in cooling system. 

If this error continues to occur, please 

contact JULABO Service. 

Summary of Contents for Presto Series


























































































































Reviews:

No comments