Javad TRIUMPH-LS User Manual Download

Page: 138 / 168

www.javad.com

138

Localization

The resulting coordinates are now displayed for the base

location with the option to save the base as a point in the

Coordinate List. I have selected “Yes”, and pressing “OK”

leads to the Point Name screen, where I have named the

new base location “Base1”.

Now that we have the base station coordinates determined

based on our control points, we must now return to the

base and configure it again, this time using “Select from

List” for the base position and recalling the new base point

created in localization.

All subsequently surveyed points will be related to the

autonomous base position until the base is reinitialized using

the localized base position

. Once the base is reinitialized

through SETUP>EDIT and BASE/ROVER SETUP, all

subsequently surveyed points will be related to the new

base location.

It is good practice to return to a known point,

preferably a point not used for localization if possible, and

stakeout this point to verify that the results are as expected

Single Point Localization (Unknown)

Single Point Localization To Single Point In Unknown

Coordinate System

Goal

To create a new coordinate system based on an arbitrary

grid origin. This method would be useful for creating a

coordinate system with a grid origin defined by the user

Summary of Contents for TRIUMPH-LS








































































































































































Search results

Summary of Contents for TRIUMPH-LS

Reviews:

Related manuals for TRIUMPH-LS

Brands by name

Popular brands

Javad TRIUMPH-LS, User Manual

Search results

Summary of Contents for TRIUMPH-LS

Reviews:

Related manuals for TRIUMPH-LS

Brands by name

Popular brands