INVT GD300-01A Operation Manual Download Page 113

Page: 113 / 187

Goodrive300-01A series VFD for air compressor

Fault information and fault handling

-107-

P19.13

State type

Possible cause

Solution

BIT9=1

Temperature

pre-alarm

Actual temperature detected

by PT1 is higher than the

pre-alarm temperature set

by P18.19.

• Check whether fan control

parameters are set

correctly.

• Whether the fan operates

normally.

• Fan power is too small to

dissipate heat effectively.

• Check whether there is

lubricating oil.

BIT10=1

Pressure alarm

Actual voltage detected by

P1 is larger than the alarm

voltage set by P18.18.

• Check whether solenoid

valve is normal.

• Check whether pressure

control parameters are set

correctly.

BIT11=1

Temperature alarm

Actual temperature detected

by PT1 is higher than the

alarm temperature set by

P18.20.

• Check whether fan control

parameters are correct.

• Whether

fan

operates

normally.

• Fan power is too small to

dissipate heat effectively.

• Check whether there is

lubricating oil.

BIT12=1

Pressure signal

fault

The actual voltage is

detected by P1 to be less

than 1V.

• Pressure detection sensor

is abnormal.

• Pressure detection input P1

signal wire is disconnected.

• Pressure signal interface

does not select current

signal.

BIT13=1

Temperature signal

fault

PT100 sensor is

disconnected.

• Check whether the wiring of

PT100 is normal.

• Check whether temperature

detection

sensor

abnormal.

• Temperature detection input

circuit is abnormal.

BIT14=1

Low-temperature

protection

pre-alarm

The

actual

temperature

detected by PT1 is less than

the

low

temperature

• Temperature

detection

sensor is abnormal.

• Temperature detection input

Summary of Contents for GD300-01A




























































































































































































Search results

Summary of Contents for GD300-01A

Reviews:

Related manuals for GD300-01A

Brands by name

Popular brands

INVT GD300-01A, Operation Manual

Search results

Summary of Contents for GD300-01A

Reviews:

Related manuals for GD300-01A

Brands by name

Popular brands