Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 74

Page: 74 / 162

Intel

Server System SR2612UR Service Guide

Installing the Server Board

To install the server board, follow these steps:

1. Install Motherboard into chassis by tilting the board and inserting the connectors

into the proper openings on the rear bulkhead as shown below. When the
connectors are placed into the proper openings, slowly place the board into the
chassis without causing any damage to the bottom side components.

Figure 61. Installing the server board

2. Attach the server board with nine screws.

Figure 62. Attach the screws

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands