Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 19

Page: 19 / 162

Intel

Server System SR2612UR Service Guide

Combining SATA and SAS Disk Drives

If you are combining SAS and SATA disk drives in the same enclosure, use the following
figures to plan where you will place the disk drives.

These figures represent enclosures fully-loaded with disk drives. However, the same
guidelines apply even if you are filling some of the drive slots with blank drive carriers.

Recommended Disk Drive Configurations

Figure 5. Intel

Server System SR2612UR Drive Configurations

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands