Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 51

Page: 51 / 162

Intel

Server System SR2612UR Service Guide

Installing the Operating System

The Intel

Server System SR2612UR is now ready to have the operating system installed.

Please contact your IT representative to perform this installation or if you are installing it
yourself, please follow the general guidelines below.

1. Connect the power cords to the rear of the unit.

2. Connect a monitor, keyboard, and mouse to the rear connections on the enclosure.

3. Turn on power to the enclosure by pressing the power button on the rear of the

enclosure.

4. Insert the operating system CD/DVD.

5. Follow the instructions for installing the operating system.

6. If you want to install additional drivers or programs (for the PCI cards or other

devices), you should also install them at this time.

The system is now ready to boot up. Booting the system may take several minutes.

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands