Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 50

Page: 50 / 162

Intel

Server System SR2612UR Service Guide

Figure 26. Pushing the Button on the Assembly

2. Gently pull open the lever.

The drive carrier or drive blank unlocks.

Figure 27. Drive Carrier Unlocked

3. If the enclosure is powered on, allow the disk drive to fully spin down (wait

approximately 15-20 seconds).

Warning: Removing a populated disk drive carrier before it has fully spun down may result in disk

drive damage and possible personal injury.

4. Gently pull the disk drive carrier or drive blank out of the enclosure.

5. Immediately replace the disk drive carrier assembly or install a drive blank

assembly to maintain correct airflow and cooling. For more information on
installing disk drives, see

“Installing the Disk Drives” on page 33

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands