Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 22

Page: 22 / 162

Intel

Server System SR2612UR Service Guide

Latest drivers, firmware
updates (BIOS, BMC, and
FRUSDR), and utilities

Available for download at:

http://www.intel.com/support/motherboards/server/sr2612ur/

Click the “Software and Drivers” link on the left side of the web
page.

To make sure your system
falls within the allowed
power budget

Power Budget Analysis Tool

Available at:

http://www.intel.com/support/motherboards/server/sr2612ur/

For software to manage
your Intel

server

Intel

System Management Software

Available at:

http://www.intel.com/go/servermanagement/

Table 1. Server System References

For this information or

software

Use this Document or Software

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands