Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 55

Page: 55 / 162

Intel

Server System SR2612UR Service Guide

10. Using the SATA cable supplied with the drive, route the cable from each disk drive

to the CPU server board SATA connectors.

Figure 32. Connections Diagram

11. Carefully reinstall the CPU server board air duct.

12. Reinstall the top cover and tighten the captive screw.

13. Reinstall the power cord(s).

DVD Installation

The Intel

Server System SR2612UR supports an optional DVD. Complete the following

steps to install a DVD drive in the Intel® Server System SR2612UR.

1. Ensure the AC power cord(s) are disconnected from the enclosure.

2. Remove the top cover from the enclosure by loosening the captive screw with a

Phillips screwdriver on the right rear of the enclosure.

3. Slide the top cover back and lift it from the enclosure.

4. On the rear of the enclosure, locate the removable DVD cover plate.

5. Remove the four screws and cover plate using a Phillips* screwdriver shown in the

following figure.

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands