Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 77

Page: 77 / 162

Intel

Server System SR2612UR Service Guide

Removing and Installing the Power Distribution Module

Removing the Power Distribution Module

To remove the server board, follow these steps:

1. Power down the enclosure and remove the power cord(s).

2. Remove the top cover from the enclosure by loosening the captive screw with a

Phillips screwdriver on the right-rear of the enclosure.

3. Slide the top cover back and lift it from the enclosure.

4. Remove the processor air duct.

5. Remove the PCI riser assembly.

6. Disconnect power cables, P1, P2, P3 and Front Panel logic cable, from

Motherboard as shown below.

Figure 65. Disconnect the power cables

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands