Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 131

Page: 131 / 162

Intel

Server System SR2612UR Service Guide

117

System Specifications

This appendix lists the system specifications for the Intel

Server System SR2612UR.

System Server

•

Intel

Tylersburg chipset (IOH36D, ICH10R)

•

CPUs: Up to two dual- or quad-core Intel

Xeon

Nehalem EP processors

•

Up to 12 DDR3 RDIMMs 1333Mhz (96GB max)

•

Up to five PCI-e Gen 2 slots for expansion and customization (three full height/full
length, two half height)

•

External Ports: mouse, keyboard, RS232 COM, 1Gb Ethernet (2), VGA monitor, and
USB (4)

Host Expansion/Interfaces

•

Integrated Dual 1Gb Ethernet

•

10 Gb Ethernet, Fibre Channel, SAS (selectable through PCI card)

•

SAS ports for expansion connections (on PCI card)

•

Up to 1200 MB/s throughput bandwidth (application dependant)

Measured Performance

•

Up to 750 MB/s (sustained reads)

Capacity

•

Up to 12 drives or 24 TB capacity per 2U enclosure (using available 2 TB HDDs)

Firmware

•

SCSI Enclosure Services (SES) 2.0 based firmware

Applications

•

Microsoft Windows* Storage ServerTM

•

VMware ESX*, Microsoft Hyper-VTM* and Citrix* XenServerTM virtualization

•

Open-E* Data Storage Server (DSSTM)

•

AMI StorTrends*

•

Unified NAS/iSCSI

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands