Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 54

Page: 54 / 162

Intel

Server System SR2612UR Service Guide

5. Remove the drive sled by loosening the captive thumbscrew.

Figure 30. Removing the drive sled

6. Position the drive(s) as shown and secure using the 4 screws provided with the

drive. If installing only one drive, locate the drive on the bottom shelf of the sled.

Figure 31. Installing the boot drives

7. Reinstall the drive sled and tighten down the captive thumbscrew.

8. The power cables for the 2.5-inch drives are located near the drive sled. Attach the

cable(s) to the drive(s).

9. Carefully remove the CPU server board air duct.

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands