Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 40

Page: 40 / 162

Intel

Server System SR2612UR Service Guide

SAS/SATA Midplanes

The midplane serves as the primary interface between the server board, hot-swap
backplane, and control panel. Only one midplane is offered for this system:

•

Active SAS midplane

Note: SATA connectors 6 and 7 are not used in the Intel

Server System SR2612UR.

Active Midplane

The following diagram show the location for each connector found on the active
midplane.

Figure 17. Active SAS Midplane Components

SAS Connector

Backplane Connector

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands

Intel SR2612UR - Server System - 0 MB RAM, Service Manual

Search results

Summary of Contents for SR2612UR - Server System - 0 MB RAM

Reviews:

Related manuals for SR2612UR - Server System - 0 MB RAM

Brands by name

Popular brands