Intel SR2612UR - Server System - 0 MB RAM Service Manual Download Page 48 | Manualshive

Page: 48 / 162

background image

34

Intel

®

Server System SR2612UR Service Guide

Figure 25. Pushing the Lever Until It Meets the Latch on Left Side of the Drive Slot

5. Repeat for all remaining disk drives. Drive installation is easier when installing

drives from right to left in the enclosure.

Note: To maintain proper airflow and cooling, you must install a disk drive carrier populated

with an actual disk drive or plastic drive blank assembly in every slot of the enclosure.
Under no circumstances should the appliance be operated with empty drive slots or with
empty drive carrier assemblies as this could cause damage to the LEDs on the backplane
and/or create thermal problems.

«
...
46
47
48
49
50
...
»

Summary of Contents for SR2612UR - Server System - 0 MB RAM



































































































































































Reviews:

No comments

Related manuals for SR2612UR - Server System - 0 MB RAM

Brand: NEC Pages: 74

Express5800/T120e

Brand: NEC Pages: 6

Express5800/T120e

Brand: NEC Pages: 2

Express5800/T110i

Brand: NEC Pages: 2

EXPRESS5800/R320d-E4

Brand: NEC Pages: 19

Express5800/R320d-M4 Series

Brand: NEC Pages: 98

Express5800/R120h-2M

Brand: NEC Pages: 2

Express5800/R120f-1E

Brand: NEC Pages: 12

Express5800/R120d-1E

Brand: NEC Pages: 2

Express5800/R110i-1

Brand: NEC Pages: 2

Express5800/R110h-1

Brand: NEC Pages: 40

Express5800/A2040d

Brand: NEC Pages: 83

Express5800/320Lc

Brand: NEC Pages: 4

Express5800/120Rj-2

Brand: NEC Pages: 2

Brand: NEC Pages: 106

Express5800/T120d

Brand: NEC Pages: 153

Express5800/T110g-S

Brand: NEC Pages: 128

Express5800/R120g-1E

Brand: NEC Pages: 224

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands